欢迎来到山东埃瓦德机械有限公司的网站!

当前位置:首页 > 产品中心 > 中空玻璃设备 >

中空玻璃热熔打胶机

来源:山东埃瓦德机械有限公司    日期:2018-10-29 20:12:51

中空玻璃热熔打胶机
设备简介
本公司生产的热熔打胶(WD3000)主要用于中空玻璃的外围涂胶,门窗幕墙的涂胶。热熔胶经本机给料系统加热融化后,通过机内泵升压推进,再有涂胶枪均匀涂在双层玻璃的间隔处,从而完成密封。它的特点是生产效率高,密封效果好,成本较低。(WD02-3000,此设备为双枪双泵双电机,两把胶枪可以同时工作也可以单独使用,共用一套胶仓系统)
本机属于经济实用型,具有小巧轻便,用电省,操作灵活,占用空间小等优点
 
Brief introduction
 
Hot Melt Extruder (WD3000) is mainly used for insulating glass outside the outer coating, and the sealing for door and window curtain wall . The hot melt material is heated and melted by the feeding system of the machine, and push forward through the internal pump, then the glue gun is evenly coated at the interval of the Double-layer glass, thus sealing is completed. It is characterized by high production efficiency, good sealing effect and low cost. (WD-02-3000, this equipment for dual-gun dual-pump dual-motor, two glue guns can work at the same time can be used alone, a set of plastic storage system)
 
This machine belongs to the economical and practical type, has the small light, electricity province, the operation is nimble, occupies the space to have the advantage
技术参数
电压Power : 3相,380V,50HZ
总功率Total power: 5.5KW   (7.5KW)
热熔胶仓存量Drum capability:  29KG   (最大54KG)
挤出量Glue extruer capability: 0-1kg/min
机器尺寸Machine size: 640*720*1050(1000*780*1300mm)
机器重量Machine weight: 200 KGS( 400 KGS)
 
技术介绍
本机是中空玻璃的专用涂胶设备,通常只需要单道密封,热熔胶经本机给料系统加热融化后,通过机内泵升压推进,再用涂胶枪均匀涂在双层玻璃间隔处,完成中空封闭.
在室温下制成的中空玻璃1-2分钟后即可使用,工艺相对简单,由于这种胶属于热熔性的胶,专用的挤胶设备所有管道均有加热,因此使用后无需清理设备,下次再用时重新加热即可,避免了胶的浪费.
热熔胶他是一种百分之分的固体,加热后变成热熔状态,接触空气预冷表面凝固,接着完成仅需几秒钟的时间.
This machine is a special coating equipment for insulating glass, usually only need a single channel seal, Hot melts by the machine feeding system heating melt, through the internal pump boost, and then use the glue gun evenly coated in the Double-layer glass interval, complete the hollow closed. The insulating glass made at room temperature can be used after 1-2 minutes, the craft is relatively simple, because this kind of glue belongs to the hot melt glue, the special extruding equipment ,All piping has the heating, therefore does not need to clean the equipment after the job done , it can use again directly in next time to avoid the waste of hot melt glue.
 
Hot Melt glue is a solids material, it become a hot melt condition after heating.It will become solid material again after contact the air in a few seconds.
 
主要优点如下:Advantage
1. 瞬间干燥,确保生产效率
Instant drying ,high production
2. 不需要干燥设备,节省空间
No need drying after coating,save the room
3. 无毒性,不易燃性,无污染,无公害
Non-toxic, non-flammable, non-polluting, pollution-free 4.
4. 长期储存,不会变质
Long-term storage, not bad
 
热熔打胶机胶台 Hot melt machine table
本工作台是机器的辅助平台,与主机配合可以提高工作效率,保证质量
This table is supporting hot melt coating during the work

推荐产品

快捷操作